Too Deep or Too Shallow – Can Surface Profiles be Changed by Additional Blast Cleaning?

All Archived Webinars
All Webinars


This webinar is archived and recorded from a live presentation on Monday, August 19, 2019.
Cost: FREE

To view this webinar recording, please sign in or register


Coating specifications commonly contain requirements to generate a surface profile to anchor the coating system to the steel surface. The resulting profile or anchor pattern is quantified/semi-quantified according to the three methods described in ASTM D4417 or according to the method described in ASTM D7127. The frequency and acceptability of the acquired measurements is described in SSPC PA 17.

Selection of an abrasive that is too small or too large that results in an insufficient or excessive surface profile depth, removal of an existing coating system that reveals an existing surface profile that exceeds the specification or extensive pitting of the existing steel that overtakes any surface profile created by an abrasive can result in specification deviations, non-conformities and/or project delays. It was unknown whether follow-up blast cleaning of a profiled surface (whether pre-existing or newly formed) with a smaller or larger abrasive (or different abrasive shape) would effectively and uniformly change the surface profile depth or texture across the prepared surface. Further, attempts to reduce a surface profile by holding the nozzle parallel to the surface was suspected to simply “roll-over” the peaks (rather than generate the specified depth) and decrease the peak density, thereby reducing the surface area. The net effect could be to cause potential coating detachment and lower the coating system’s resistance to undercutting when it becomes damaged in service.

A research project was conducted that consisted of preparing steel panels with small and large abrasives (to produce surface profiles that are too deep and too shallow), re-preparing the surfaces using smaller/larger abrasives in an attempt to bring the surface profiles “into conformance,” then characterizing the surface according to ASTM D4417, methods B and C, peak density measurements using special replica tape and a replica tape reader, as well as the two surface characterizations described in ASTM D7127 (Rt and Rpc). The change in the shape of the surface profile was examined using 3D microscopy together with digital microphotographs of the surfaces. This webinar will describe the potential impact of insufficient/excessive surface profile on production and quality as well as present the results of the research initiative.

Learning Objectives:

• Describe the process of generating a surface profile;
• Recognize the impact of insufficient or excessive surface profile on coating performance;
• Describe the process of increasing or decreasing surface profile; and
• Recognize the impact of reducing surface profile on peak density/count.


Presenter:

Bill Corbett, Chief Operations Officer
KTA-Tator, Inc.

Bill is the Chief Operations Officer for KTA-Tator Inc. (KTA), where he has been employed for 40 years. He holds an AD in Business Administration from Robert Morris University. He is an SSPC Certified Protective Coating Specialist, an SSPC Level 3 Certified Protective Coatings Inspector and a Level 2 Certified Bridge Coatings Inspector, as well as a NACE Level 3 Certified Coatings Inspector. He is an approved training course instructor for both SSPC and KTA. He received SSPC’s Coating Education Award in 2006, the John D. Keane Award of Merit in 2011 and the President’s Lecture Series Award in 2017. He is the Chair of the SSPC Dry Film Thickness Committee and Chair of the SSPC Education and Certification Committee. He is also a member of ASTM Subcommittees D01.23 and D01.46.

Downloadable File:
(right-click and choose 'Save Target As' to download; all downloads are copyright of their author.)



Tagged categories: Abrasive blasting; Abrasives; Blast profile; Blasting; Blasting nozzles; KTA-Tator; North America; PaintSquare; Surface Preparation; Surface preparation; Surface preparation equipment


Technology Publishing Co., 1501 Reedsdale Street, Suite 2008, Pittsburgh, PA 15233

TEL 1-412-431-8300  • FAX  1-412-431-5428  •  EMAIL webmaster@paintsquare.com


The Technology Publishing Network

PaintSquare the Journal of Protective Coatings & Linings Paint BidTracker

 
EXPLORE:      JPCL   |   PaintSquare News   |   Interact   |   Buying Guides   |   Webinars   |   Resources   |   Classifieds
REGISTER AND SUBSCRIBE:      Free PaintSquare Registration   |   Subscribe to JPCL   |   Subscribe to PaintSquare News
MORE:      About PaintSquare.com   |   Privacy Policy   |   Terms & Conditions   |   Support   |   Site Map   |   Search   |   Contact Us