Problem Solving Forum (31)


During a week of heavy rain, we painted the interior walls of a heated concrete building. On the interior of walls that had an outside exposure, the paint blistered badly a week after the rain subsided. Could the rain have caused the blistering and, if so, how?


How does rapid depressurization affect lining performance in vessels and line pipe, and how can you identify any failure that might result?


What is the Cold Wall Effect? Can it cause premature coating failure and, if so, how do I prevent or minimize it?


What is the best way to repair localized coating breakdown on steel?


During a week of heavy rain, we painted the interior of a heated concrete building. The paint blistered badly a week later on the walls with an outside exposure. What’s the best way to remove the coating, prepare the surface, and recoat to prevent future blistering?


What is the best way to repair localized coating breakdown on steel?


What causes blistering/crater formation in freshly applied polyurethane topcoats, and how can this be avoided?


How do you protect concrete against microbiologically influenced corrosion?


What is the most important factor to determine in a failure investigation and why is it so?


How does rapid depressurization affect lining performance in vessels and line pipe, and how can you identify any failure that might result?


How do you repair delaminated areas of an elastomeric polyurea when the majority of the coating system is intact?


What is the Cold Wall Effect? Can it cause premature coating failure on a building and, if so, how do I prevent it?


What causes blistering/crater formation in freshly applied polyurethane topcoats, and how can this be avoided?


What is the best way to repair localized coating breakdown on steel?


What causes bubbling or cratering of epoxy intermediate coat when applied over epoxy zinc-rich primer?


Animal fat in slaughterhouses often penetrates concrete surfaces. If the fat is not removed before the concrete is coated, the fat can cause the coating to fail. How do you identify and remove the contamination before coating the concrete?


What is the most important factor to determine in a failure investigation and why is it so?


What coating problems are likely in storage tanks that have dissimilar metal sides and floors?


How can it be determined if moisture within a CMU wall is causing repeated coating failure? If so, can the source of moisture entry be accurately identified for correction?


How do you protect concrete against microbiologically influenced corrosion?


How does rapid depressurization affect lining performance in vessels and line pipe, and how can you identify any failure that might result?


Does the presence of non-burst blisters in a coating system always mean that the coating requires replacement?


What is the Cold Wall Effect? Can it cause premature coating failure and, if so, how do I prevent it?


During a week of heavy rain, we painted the interior of a heated concrete building. The paint blistered badly a week later on the walls with an outside exposure. What’s the best way to remove the coating, prepare the surface, and recoat to prevent future blistering?


During a week of heavy rain, we painted the interior walls of a heated concrete building. On the interior of walls that had an outside exposure, the paint blistered badly a week after the rain subsided. Could the rain have caused the blistering and, if so, how?


What is the best way to repair localized coating breakdown on steel?


What causes blistering/crater formation in freshly applied polyurethane topcoats, and how can this be avoided?


How can it be determined if moisture within a CMU wall is causing repeated coating failure? If so, can the source of moisture entry be accurately identified for correction?


Under what conditions should small-diameter blisters (<1.5 inches) in a water tank lining be repaired/repainted? Should the blisters be broken and the substrate examined?


How does rapid depressurization affect lining performance in vessels and line pipe, and how can you identify any failure that might result?


What is the Cold Wall Effect? Can it cause premature coating failure and, if so, how do I prevent or minimize it?


 
 
   

**Commercial white papers, product videos, and other sponsored documents posted on this site are paid content from third-party companies; inclusion and posting on this site does not imply an endorsement nor recommendation of the content by Technology Publishing/PaintSquare. By signing in and viewing or downloading this paid content, you agree to make your name and full contact information available to the sponsor of the content.

Advertisements
 
Fischer Technology Inc.

 
KTA-Tator, Inc. - Corporate Office

 
Sauereisen, Inc.

 
SAFE Systems, Inc.

 
Tarps manufacturing, Inc.

 
ABKaelin, LLC

 
Mitsubishi Gas Chemical America

 
Modern Safety Techniques

 
HoldTight Solutions Inc.

 
NLB Corporation

 

Technology Publishing Co., 1501 Reedsdale Street, Suite 2008, Pittsburgh, PA 15233

TEL 1-412-431-8300  • FAX  1-412-431-5428  •  EMAIL webmaster@paintsquare.com


The Technology Publishing Network

PaintSquare the Journal of Protective Coatings & Linings Paint BidTracker

 
EXPLORE:      JPCL   |   PaintSquare News   |   Interact   |   Buying Guides   |   Webinars   |   Resources   |   Classifieds
REGISTER AND SUBSCRIBE:      Free PaintSquare Registration   |   Subscribe to JPCL   |   Subscribe to PaintSquare News
MORE:      About PaintSquare.com   |   Privacy Policy   |   Terms & Conditions   |   Support   |   Site Map   |   Search   |   Contact Us