PaintSquare.com
      | Connect Follow us on Twitter Like us on Facebook
About | Subscribe | Advertise
  

 

Download our free e-book! Corrosion Under Insulation. Sponsored by Thermion.

 

Problem Solving Forum (17)


What are the criteria for selecting coatings for application during extreme (atmospheric) heat?


If the walls of single-wythe CMU with core fill insulation become saturated, can they be adequately dried out for painting? If so, how?


What can be done to prevent rust bleed in crevices when applying a zinc/epoxy/urethane system?


What are the criteria for selecting coatings for application during extreme (atmospheric) heat?


What is the best way to ensure successful application of an acid stain to an existing horizontal concrete surface?


Where can I find industry standards for air quality during spray painting operations, specifically regarding moisture, oil and particulates?


Is it sufficient to specify simply that paint should be applied "according to the manufacturer’s instructions?" If not, what detail should be included?


How does one apply thin polymer coatings to installed tubes or pipes with diameters of one to three inches and lengths of 20 to 60 feet?


How do you prepare flame-cut edges for application of thermal spray metallic coatings? The problem is that these edges are often harder than the abrasive, so a very low profile is produced, resulting in lower-than-specified adhesion of the thermal spray to the steel.


What are some ways to improve transfer efficiency of airless spray application?


What differences in performance and speed do you see among plural-component, conventional airless, and conventional air spraying equipment for field painting structural steel?


How many times can a building be repainted before the paint becomes too thick to perform properly?


How long after blasting can stainless steel be left before painting? If this time is exceeded, what further surface preparation is required?


How do you adequately assess the adhesion of a newly applied coating?


How do you successfully apply a chemical-resistant lining to the interior of small-diameter pipes (3 inches or less)?


What is the effect on the permeability of a coating when you add additional coats, either at the time of the original painting or as a maintenance activity?


Is it sufficient to specify simply that paint should be applied "according to the manufacturer’s instructions?" If not, what kind of detail should be included?


 
 
   

Specialty Products, Inc. (SPI)
Polyurea & Polyurethane Spray Foam Training

SPI is committed to industry leading technical training for polyurea & polyurethane spray foam professionals. Attendees receive hands-on, in-depth training for using and troubleshooting plural-component equipment, spray guns, machine hoses & parts.


N.T. Ruddock Co.

Our Abrasives Hold Up Under Pressure

N. T. Ruddock focuses on abrasive selection, equipment evaluation, equipment maintenance & reduction of abrasive consumption. Other services include Screen Analysis & Background Radiation Testing.


Novetas Solutions
Number 1 Crushed Glass Abrasive in America!

Manufactured from 100% Recycled Glass.
NO Crystalline Silica,
Beryllium & Arsenic
Great White Metal Finish!
4 plants on Navy QPL
Call us at 866-775-6226


Nationwide Overspray
Profession Overspray Removal Services

The Finest Name in Safe Overspray Removal. We specialize in removing all contaminants from any surface. Family Owned and Operated for 33 years! Fully insured. Satisfaction is guaranteed.


Titan Tool, Inc.
Power, Precision, Reliability. Titan PowrCoat Series.

PREMIUM COMES STANDARD. Power, precision and reliability are built into each unit including Severe Service which means twice the life with no maintenance. For maximum uptime, durability and ease of use, nothing performs like the PowrCoat™ from Titan.


Sherwin-Williams
Sherwin-Williams Protective & Marine Coatings

With 4,000 distribution points and 3,700+ years of experience, Sherwin-Williams delivers the products, support and expertise you need, right where you need it.


HoldTight Solutions Inc.
NO FLASH RUST -
NO CONTAMINANTS

Our HoldTight®102 salt remover & flash rust preventer prevents flash rust by removing surface contaminants. It has no equal; only wannabees.
Contact us for your
nearest distributor.
(800) 319.8802 sales@holdtight.com


PPG Protective and Marine Coatings Group
Bringing innovation to the surface.™

PPG Protective & Marine Coatings is widely recognized as a world leader in protective and marine coatings, developing innovative, cutting-edge products and services.


PreTox Products - NexTec, Inc.
GOT LEAD? Specify Pretox System products

The ONLY Lead Stabilizer Compatible with All Paint Removal Methods. Works with all Blast Media: Grits | Recyclable Abrasives | CO2 | Water | Power Tools | Etc. Call Dave Steffen at 800.338.8296.

 
Technology Publishing

The Technology Publishing Network

The Journal of Protective Coatings & Linings (JPCL) PaintSquare
Durability + Design Paint BidTracker

 
EXPLORE:      JPCL   |   PaintSquare News   |   Interact   |   Buying Guides   |   Webinars   |   Resources   |   Classifieds
REGISTER AND SUBSCRIBE:      Free PaintSquare Registration   |   Subscribe to JPCL   |   Subscribe to PaintSquare News
MORE:      About PaintSquare.com   |   Privacy policy   |   Terms & conditions   |   Site Map   |   Search   |   Contact Us
 

© Copyright 2000-2016, Technology Publishing / PaintSquare, All rights reserved
2100 Wharton Street, Suite 310, Pittsburgh PA 15203-1951; Tel 1-412-431-8300; Fax 1-412-431-5428; E-mail webmaster@paintsquare.com