|
from JPCL, December 2017 ; by Carl Reed, Greenman-Pedersen, Inc. (GPI), and Dr. Mike O’Donoghue and Vijay Datta, MS, International Paint LLC
This article examines the flaws of the current system of establishing and using speci...
|
|
from JPCL, June 2017 ; by Rob Lanterman, KTA Tator, Inc.
Disbonding of an Overcoat
|
|
from JPCL, March 2017 ; by Michael F. Melampy, PPG Protective and Marine Coatings
This article focuses on protective coatings as part of a three-pronged approach to pr...
|
|
from JPCL, February 2017 ; by Carl W. Reed, GPI Laboratories, Inc., and Kat Coronado, International Paint, LLC
This article examines the four predominant sources of corrosion that occur “in the wi...
|
|
from JPCL, December 2016 ; by James D. Machen, KTA-Tator, Inc.
|
|
from JPCL, November 2016 ; by Dr. Yasir Idlibi, MICHAL Consulting; Jason Hartt, ADANAC Global Testing & Inspection; Dr. Mike O’Donoghue and Vijay Datta, MS, International Paint LLC; and Bill Johnson, AScT, Acuren Group Inc.
Is there such a thing as “blind chance”? Enter the realm of cause and effect and lini...
|
|
from JPCL, September 2016 ; by Chrissy M. Stewart, PCS Senior Chemist, KTA-Tator, Inc.
|
|
from JPCL, February 2016
|
|
from JPCL, February 2016 ; by Bruce J. Wiskel, P.E., Pacific Gas & Electric Company; and J. Peter Ault, P.E., Elzly Technology Corporation
The authors discuss the challenges of applying coatings to transmission pipeline when...
|
|
from JPCL, December 2015 ; by Dwight G. Weldon, Weldon Laboratories, Inc.
The author describes cases where recognizing patterns used in conjunction with standa...
|
|
from JPCL, November 2015 ; by Mike O'Donoghue, Ph. D. and Vijay Datta, M.S., International Paint LLC
The authors compare and contrast the accelerated laboratory autoclave performance of ...
|
|
from JPCL, November 2015
|
|
from JPCL, September 2015 ; by Chrissy M. Stewart, PCS; Richard A. Burgess, PCS, Series Editor; KTA-Tator, Inc.
|
|
from JPCL, July 2015 ; by Dwight G. Weldon, Weldon Laboratories, Inc.
|
|
from JPCL, February 2015 ; by Emre Aksu, Borusan Mannesmann and Alan Kehr, Alan Kehr Anti-Corrosion, LLC
The authors discuss cathodic disbondment testing of fusion-bonded epoxy and three-lay...
|
|
from JPCL, January 2015 ; by Dwight G. Weldon, Weldon Laboratories, Inc.
Even if the cause of the failure is not
obvious upon microscopic examination, clues ...
|
|
from JPCL, December 2014 ; by Dwight G. Weldon, Weldon Laboratories, Inc.
|
|
from JPCL, October 2014 ; by Dwight G. Weldon, Weldon Laboratories, Inc.
|
|
from JPCL, The Facility Owner's Perspective 2014 Special Issue; by Dr. Mark R. Kolody, Jerome P. Curran and Dr. Luz Marina Calle, NASA Corrosion Technology Laboratory
This article discusses the test protocol required for coating systems to be included ...
|
|
from JPCL, June 2014
|
|
from JPCL, November 2013 ; by Dr. David Tordonato, P.E., and Dr. Allen Skaja, P.C.S., U.S. Bureau of Reclamation
The authors discuss the use of metalizing, or thermal spray coating (TSC) application...
|
|
from JPCL, Three Decades of Change in the Coatings Industry 2013 Special Issue; by The JPCL Staff
|
|
from JPCL, July 2013
What action should be taken if an inorganic zinc (IOZ) fails the MEK test?
|
|
from JPCL, May 2013 ; by Charles Lange, JPCL
|
|
from JPCL, April 2011
|
|
from JPCL, August 2010 ; by JPCL staff
Based on information provided to JPCL about products introduced between June 2009 and...
|
|
from JPCL, March 2010 ; by John Bullard, Port Authority of New York & New Jersey, and William D. Corbett, KTA-Tator, Inc.
In this article, the authors report on the surface preparation and
coating system se...
|
|
from JPCL, January 2010 ; by Valerie Sherbondy, Senior Chemist, KTA-Tator, Inc., and Richard Burgess, KTA-Tator, Inc., Series Editor
Maintenance takes drawbridge from bad to worse
|
|
from JPCL, December 2009 ; by Rick A. Huntley, Senior Coatings Consultant, KTA-Tator, Inc.; Richard Burgess, KTA-Tator, Inc., Series Editor
The Case of the Failing Floor Coating
|
|
from JPCL, November 2009 ; by Andreas W. Momber, Ph.D., Muehlhan AG; Peter Plagemann, Ph.D., and Volkmar Stenzel, Ph.D., Fraunhofer Institute for Manufacturing and Applied Materials Research; and Michael Schneider, Ph.D., Fraunhofer Institute for Ceramic Technologies and Systems
In Part 3 of a three-part series, the authors report on corrosive stress on offshore ...
|
|
from JAC, October/November 2009
From technical functions to design services, from project management to spec writing,...
|
|
from JPCL, August 2009 ; by Michael Donkin, International Paint Ltd.
Massive changes have occurred in coating formulation for the heavy-duty market in the...
|
|
from JPCL, June 2009
|
|
from JPCL, March 2009 ; by Shuang-Ling Chong, Federal Highway Administration (retired 2007), and Yuan Yao, SES Group & Associates
This article discusses the various accelerated laboratory test methods that have been...
|
|
|
|
**Commercial white papers, product videos, and other sponsored documents posted on this site are
paid content from third-party companies; inclusion and posting on this site
does not imply an endorsement nor recommendation of the content by Technology Publishing/PaintSquare.
By signing in and viewing or downloading this paid content, you agree to make your name and full contact
information available to the sponsor of the content.
|
|