PaintSquare.com
Follow us on Twitter Follow us on LinkedIn Like us on Facebook Follow us on Instagram Visit the TPC Store
Search the site

 

Advertisement

PaintSquare


Problem Solving Forum

| More

February 11 - February 17, 2013

Can water be sprayed onto an IOZ coated surface, which has not fully cured due to low humid conditions, to accelerate the cure?

More items for Coating Materials


Selected Answers

From Krishnan Swaminathan of Central Electrochemical Research Institute, India, Research in Protective Coating field for 27 years on February 15, 2013:
yes

From Stephen Cantrelle of Concord Terrazzo on February 18, 2013:
     Yes. Allow solvent to flash off first.

From Simon Hope of Bilfinger Salamis on February 18, 2013:

     It is absolutely essential that IOZ is subjected to water, as it is needed as part of the chemical reaction to obtain chemical cure. IOZ will not cure in low humidity even though it seems to be dry; this is one of the most common failures to manifest as an apparent cohesive failure. Water must be present. High humidity is best, but a fine spray applied to the entire structure will work once the IOZ is through dry. It is essential to check the degree of cure using a white rag soaked in solvent, gently rubbed on the surface to ensure no material is dissolved. Once the IOZ is cured, it is imperative that the coating is thoroughly dried before the application of the sealer coat; otherwise, you will have reaction of the zinc to form oxide and the inevitable disbonding again!

From Karen Oscarson of PPG on February 15, 2013:
     Yes, that is common practice in geographically arid parts of the world.

From S. Matsumoto of Abraco on February 15, 2013:
I have similar experience. Spray water but do not wash after a couple of hours.

From Ahmed Abd Ellatif of ENPC on February 28, 2013:
     Yes, apply water if the relative humidity is below 65% but wait for 2 hours after application and use water with a low salt percentage because  salt will delay the curing.

From Stephen Bothello of Jotun Paints on February 20, 2013:
     Yes, water can accelerate the cure. However, it's better to check with the coating manufacturer before taking this step. Seldom at low relative humidity levels below 30%, even with repeated water spray, it may not cure, depending on the product formula, and  all uncured coating may need to be removed. This can therefore be confirmed only by the coating manufacturer's technical representative. In inorganic zinc silicates the curing/optimum strength development is by the hydrolysis reaction (addition of water) of the inorganic silicate binder/ polymer. A major part of this hydrolysis reaction is executed in the factory during production process by adding calculated amount of water and catalyst. The balance of the hydrolysis reaction has to be completed by water molecules from  atmospheric humidity (after mixing & application). Most hydrolysis reactions are normally standardised by the manufacturers at 60% to 75 % atmospheric relative humidity levels. Lower than this humidity level  will require external water spray (mist spray is sufficient,  not high pressure spray ). At exceptionally low relative humidity levels (generally below 35%), it's better to call the manufacturer's technical representative and ask for technical advise/ intervention before application. Completion of this reaction to optimum levels/ cure state is assessed by the mandatory MEK rub test (ASTM D 4752). A rating minimum of 4 is good enough and 5 considered excellent for cure and strength development for subsequent coating with epoxy midcoat/ other coatings. Coin rub test for burnishing effect can be used as an additional confirmatory test to confirm curing over large/ entire area.

From Jayakrishnan Radhakrishnan of Sigma Paints Saudi Arabia Limited on February 14, 2013:
    Yes, after approximately 4 hours of application, the primed surface should be wetted or soaked with clean water for 2 hours, followed by complete drying.

From Grant Kirby-Smith of Jotun Paints on February 11, 2013:
     Yes, provide it has dried for at least a couple of hours or it will wash off. Always conduct an MEK rub test + coin test to ensure the primer is cured before overcoating.

From Farooq MD of RasGas on February 12, 2013:
yes

From Dipesh Vyas of CARBOLINE on February 15, 2013:
     It is recommended to maintain humidity by sprinkling /spraying or misting of water but not by soaking /immersing after a minimum of 2 hrs of cure ( 23 C), and check after every 3-4 hours to determine if required step can be repeated . It is as good as cement in the way it drinks water till it becomes hard rock. IOZ curing is also more or less similar.

From willem van Gent of corrcon Marine on February 10, 2013:
     I have experience on hatch covers in Korea where we use water spray in the winter time when the humidity is very low on IOZ primer after spray application with a good result.

Please sign in to submit your answer this question    

Tagged categories: Curing


Current PSF Question | Submit a PSF Question | Full PSF Archive

Advertisements
 
BASF
 
New resins from BASF will have metals loving water!
 
Excellent corrosion resistance, low VOC, high gloss, thin films www.basf.us/industrialcoatings dpsolutions@basf.com 800-231-7868
 

 
Mitsubishi Gas Chemical America
 
Performance Amine 1,3-BAC
 
A highly reactive cycloaliphatic diamine offering superior performance. Reasonable cost and curing efficacy makes it suitable for all types of epoxy resin applications.
 

 
Sherwin-Williams
 
Sherwin-Williams Oil & Gas App
 
Our coatings and linings expertise available 24/7, allowing you to explore the best Sherwin-Williams solutions for oil refineries, shale drilling sites, and offshore. Android users
click here. Download today!
 

 
SAFE Systems, Inc.
 
Portable Blast &
Recovery Equipment
 
Trailer or skid mounted blast and recovery equipment. Systems designed for maximum versatility, environmental compliance
and overall cost savings.
Call 1-800-634-7278
 

 
Carboline Company
 
Fireproofing Solutions
 
Pyroclad® X1 Thermo-Lag® Pyrocrete® – protecting against hydrocarbon and jet fires, explosions, and cryogenic spills.
 

 
PPG Protective and Marine Coatings Group
 
We Protect and Beautify the World
 
PPG is widely recognized as a world leader in protective and marine coatings, developing innovative, cutting-edge products and services.
 

 
Jotun Paints Inc.
 
Jotachar JF750 - The Time Saving Solution
 
The only mesh free solution for jet fire scenarios. Jotachar saves installation time and material costs - the next generation of epoxy passive fire protection.
 

 
Detail Masters
 
Overspray Removal
 
We offer professional, turnkey service and unparalleled quality!
Our process can save hundreds— even thousands of dollars. It's fast, environmentally safe and 100% guaranteed.
 

 
Tnemec Company, Inc.
 
Online Coating Courses from Tnemec
 
For decades, Tnemec has offered its expertise to clients presenting face-to-face coatings courses. Now, these presentations are available to anyone for CEUs at Tnemec University.
 

 
International Bridge Conference
 
2017 International Bridge Conference
 
June 4-8, 2017, National Harbor, Maryland
 

 
 
 

Technology Publishing Co., 2100 Wharton Street, Suite 310, Pittsburgh PA 15203-1951

TEL 1-412-431-8300  • FAX  1-412-431-5428  •  EMAIL webmaster@paintsquare.com


The Technology Publishing Network

Durability + Design PaintSquare the Journal of Protective Coatings & Linings Paint BidTracker

 
EXPLORE:      JPCL   |   PaintSquare News   |   Interact   |   Buying Guides   |   Webinars   |   Resources   |   Classifieds
REGISTER AND SUBSCRIBE:      Free PaintSquare Registration   |   Subscribe to JPCL   |   Subscribe to PaintSquare News
MORE:      About PaintSquare.com   |   Privacy policy   |   Terms & conditions   |   Site Map   |   Search   |   Contact Us