PaintSquare.com
      | Connect Follow us on Twitter Like us on Facebook
About | Subscribe | Advertise
  

 

Paint and Coatings Industry News

Main News Page


Drilling of Decaying Monument to Begin

Tuesday, November 2, 2010

Comment | More

Gateway Arch

Contractors will soon begin drilling into the steel-and-concrete Gateway Arch in St. Louis to create monitoring ports and obtain core samples as authorities deepen their study of the growing corrosion plaguing the nation’s tallest monument.

A structural steel study, commissioned in September, is now underway to determine the cause and extent of the decay and staining on both the stainless-steel exterior and carbon-steel interior of the iconic Arch, which opened in 1967, eight years after groundbreaking.

Coating Plan

The Arch’s exterior never received a protective coating, because planners and builders considered stainless steel impervious to corrosion. Cleaning every 50 years was all that was required for the structure to last 1,000 years, they said.

Time proved otherwise, however, with interior and exterior corrosion and decay becoming visible over the years. The study now underway follows one conducted in 2006 that reportedly noted corroding bolt heads and staircases; a leaky, sometimes-fog-shrouded, rusting interior; and a degenerating exterior.

Some sort of battleship-gray lead-based protective coating was applied to the interior during construction, but except for spot repairs and touch-ups, the reinforced-concrete-and-steel structure has never been recoated or even thoroughly cleaned, according to the National Park Service.

Monitoring and Data Collection

Consultants are now mapping up to two dozen spots in the concrete fill area where ports will be drilled into the legs, said Frank Mares, deputy superintendent of the Jefferson National Expansion Memorial, which includes the Arch. The concrete fill area extends about 300 feet up the Arch legs; above that, the structure is steel only.

Gateway Arch

The holes—about a dozen in each leg—will range in size up 10 inches wide, Mares said. Some will be used to obtain concrete core samples of a depth yet to be determined. Other ports will be used to install humidity and temperature sensors—and, later on, possibly cameras—to gather data and monitor the corrosion. Those areas will be covered with removable plates,

Other monitors will be installed on the higher steel-only sections to analyze the composition of the area and obtain a better view of the damage, Mares said. The data will be collected for about a year, beginning in January.

Although Park Service officials say the structure is safe, they also acknowledge that they cannot yet determine the extent of the damage.

Tracking Moisture

Part of the current effort will be to determine the source of the moisture infiltration. “Water is in there somehow, and it’s hard to say how,” Mares said.

Among the possibilities:

• Leaking into the ventilation louvers installed on top of the Arch. However, the louvers are inspected annually and officials consider this the least likely possibility.

• Infiltration through welds and seams—a strong possibility, but perhaps not the whole problem, officials say.

• Naturally occurring condensation that results from fluctuations in temperature and humidity extremes. Again, some of this is almost a certainty, but officials want to know how the corrosion became so advanced.

• A problem with the concrete, perhaps caused by the addition of a chemical curing agent during construction.  This is a new suspicion, and a strong one, Mares said.  “Normally, a curing agent isn’t a problem,” he said, “but when you seal it up like a tomb, that could cause a problem.”

Consultants are now examining archival records to more precisely determine the structure’s coatings and concrete formulations, Mares said.

Gaining Access

Also on the consultants’ to-do list: Determine a way to fully access the structure’s exterior, to collect samples and eventually make repairs.

“We presume that it will involve some sort of rappelling,” Mares said. “Cranes could reach it, but there’s really no way to bring a crane in.”

When the Arch was constructed, two 100-ton creeper derricks were used to raise the 12-foot-high, 50-ton sections at the top. Workers then used the derricks to apply the final touches, welding, grinding, polishing and cleaning as they worked their way down the structure.

Study Schedule

All of the mapping and research work must be completed within about a month to allow for review for historical compliance, lead abatement and other issues, Mares said.  Officials plan to keep the structure open throughout the study period.

Park Service employees will perform the drilling and other work once the plan is approved. After a year of data collection, Mares said, the consultant’s report should be available in January 2012, and the actual restoration and repairs can proceed.

“The aesthetic prettying-up of it,” he added, “will be the least of the problem.”

   

Tagged categories: Corrosion; Stainless steel; Structural steel

Comment from Loren Hatle, (11/3/2010, 10:05 AM)

Whether it be carbon steel or stainless, take into consideration sulfide inclusion, albeit it is non-water soluble or visible, I believe sulfide inclusion is a major threat to potential corrosion failure of infrastructure. There is a solution.


Comment Join the Conversation:

Sign in to our community to add your comments.

Termarust Technologies
Termarust (HR CSA) Chemically Stops
Active Corrosion

Truss bridge treated in 2000 with Termarust's (HR CSA) field-proven rust mitigation system chemically stopped corrosion, crevice corrosion & pack rust.


U.S. Zinc
Historic Reliability. Innovative Performance.

The reliable protection properties of our zinc dust help combat deterioration and corrosion in your paints and coatings. U.S. Zinc - Helping the world work™


Chicago Corrosion Group
Vendor-neutral corrosion consulting

What you don’t know about painting is costing you a fortune. Call today to see how CCG’s vendor-neutral, owner’s advocacy saves our clients millions.


HoldTight Solutions Inc.
NO FLASH RUST -
NO CONTAMINANTS

Our HoldTight®102 salt remover & flash rush inhibitor prevents flash rust by removing surface contaminants.
Contact us for your nearest distributor. (800) 319.8802 sales@holdtight.com


International Paint LLC

International Paint Engineered Coatings

Learn about our solutions for:
  • Structural Steel
  • Piping & Equipment
  • Storage Tanks
  • Pressure Vessels
  • Secondary Containment


    KTA-Tator, Inc. - Corporate Office
    KTA Analyzes
    Coating Failures

    • Field Diagnosis
    • Lab Diagnosis
    • Determination of Cause
    • Recommendations
    www.kta.com
    800-245-6379


    Abrasives Inc.
    Check our Prices for Blast Abrasives

    Faced with higher abrasive costs? We invite you to call & check our rates on Black Magic® coal slag and other quality blast materials. Abrasives Inc. 800-584-7524


    Trelawny Surface Preparation Technology
    Surface Preparation Equipment

    Manufacturer of needle scalers, grinders, scarifiers and scabblers. Pneumatic tools for Marine and Construction. US distributor CS Unitec: 800-700-5919


    Industrial Vacuum Equipment Corp.
    Hurricane Vacuums
    & Dust Collectors

    Vacuum and dust collector hose, filters and related accessories.
    IndustrialVacuum.com

  •  
     
     
    Technology Publishing

    The Technology Publishing Network

    The Journal of Protective Coatings & Linings (JPCL) PaintSquare
    Durability + Design Paint BidTracker

     
    EXPLORE:      JPCL   |   PaintSquare News   |   Interact   |   Buying Guides   |   Webinars   |   Resources   |   Classifieds
    REGISTER AND SUBSCRIBE:      Free PaintSquare Registration   |   Subscribe to JPCL   |   Subscribe to PaintSquare News
    MORE:      About PaintSquare.com   |   Privacy policy   |   Terms & conditions   |   Site Map   |   Search   |   Contact Us
     

    © Copyright 2000-2015, Technology Publishing / PaintSquare, All rights reserved
    2100 Wharton Street, Suite 310, Pittsburgh PA 15203-1951; Tel 1-412-431-8300; Fax 1-412-431-5428; E-mail webmaster@paintsquare.com